Skip to content
Bright SunMetal Panels & RoofingRoof line, 24/7(407) 783-0064

Metal roofing

Standing Seam Metal Roofing in Orlando, FL

Standing seam is the metal roof most Orlando homeowners picture: smooth panels, raised seams, and no exposed screws for the sun and rain to work on.

Standing seam metal roof in charcoal gray on a one-story Orlando home with palm trees and a bright blue sky
Most common reason people callYour shingles are past 15 years and the insurance renewal asked about roof age.
In one paragraph

We measure and cut panels to your roof, set a high-temperature underlayment over the deck, and finish the ridge, hips and valleys with trim bent to match. Typical cost in Orlando runs $11.85 to $17.40 per sq ft installed, tear-off included on a typical one-story home, and the roof line answers 24/7 at (407) 783-0064.

How we handle standing seam metal roofing

Each panel runs from ridge to eave in one length, and the seams lock together above the flat of the roof, so water never sits on a fastener. The clips that hold the panels let them slide a little as the metal heats up in a July afternoon and cools off when a thunderstorm rolls through at 4 pm. That movement is what keeps the seams tight for decades instead of a few summers.

On most Orlando houses a full standing seam roof takes four to seven working days once the material arrives, and the house stays dry each night because we only open what we can close the same day.

Good reasons to call

  • Your shingles are past 15 years and the insurance renewal asked about roof age
  • You want a roof that sheds Central Florida storms without exposed screws
  • Granules from the old shingles are piling up in the gutters
  • You plan to stay in the house long enough to outlast two shingle roofs
  • You want a lighter, cooler color that reflects afternoon sun

Step by step

What the job looks like

01

Measure and pick the panel

We measure every plane, then go over mechanical lock vs snap lock, panel width and finish color with you.

02

Strip to the deck

Old roofing comes off in sections, and any soft or rotten sheathing gets replaced before anything new goes down.

03

Underlayment and trim

High-temperature underlayment goes over the whole deck, then drip edge, valley and eave trim.

04

Panels, ridge and walk-through

Panels are clipped and seamed, the ridge is vented and capped, and we walk the finished roof with you.

Options

Choices you will make

Snap-lock panels

Faster to install and a good fit for most homes with a 3/12 pitch or steeper.

Mechanically seamed panels

Seams are folded with a seaming tool for low slopes and the highest wind ratings.

Galvalume vs painted finish

Bare Galvalume costs less; a factory paint finish adds color and stronger fade resistance.

$11.85 to $17.40

Typical standing seam metal roofing cost in Orlando: per sq ft installed, tear-off included on a typical one-story home. Final price depends on roof size, pitch, access and what we find under the old roofing.

Compare every service on the Orlando roof price guide

Close view of raised standing seam ribs and a vented ridge cap on a new metal roof in Central Florida
Close view of raised standing seam ribs and a vented ridge cap, photographed on a recent job in the Orlando area.

Questions we hear

How long does a standing seam roof last in Orlando?

With a factory paint finish and correct clips, most standing seam roofs here run 40 to 60 years. Fasteners are hidden, so there are no screws to reseal along the way.

Is a metal roof louder in the rain?

Over a solid deck with underlayment and an insulated attic, rain on standing seam sounds about the same as rain on shingles inside the house.

Can standing seam go on a low-slope roof?

Yes. Mechanically seamed panels are made for slopes down to about 1/2 in 12, which suits many Florida porch and addition roofs.

Related work

Often booked together

5V Crimp Metal Roofing

5V crimp is the old Florida metal roof, the one you still see on cracker houses around Lake County, and it remains one of the most affordable metal options for an Orlando home.

5V Crimp Metal Roofing details

R-Panel Metal Roofing

R-panel and PBR metal roofs cover a lot of square footage for the money, which is why they are on so many shops, barns and commercial buildings around Orange and Lake County.

R-Panel Metal Roofing details

Metal Roof Replacement

A metal roof replacement takes off what is up there now, shingle, tile or old metal, and puts down a new panel system built for Central Florida weather.

Metal Roof Replacement details

Stone-Coated Steel Roofing

Stone-coated steel gives you the look of shingle, shake or barrel tile with the weight and wind resistance of a steel roof.

Stone-Coated Steel Roofing details

Where we do standing seam metal roofing

OrlandoWinter ParkKissimmeeCollege ParkLake NonaDr. PhillipsSanfordApopkaClermontConwayAll 57 areas

Roof trouble today? Call the roof line.

Real roofers answer 24/7, and we come out to Orlando and the nearby cities every day of the week.

(407) 783-0064
Call (407) 783-0064